Roof roof by profiled sheet with your own hands. Installation of corrugated board on the roof

A corrugated metal roof installation can be a useful and affordable way to improve the aesthetic appeal of your home while shielding it from the elements. Because they are strong, lightweight, and reasonably simple to install, corrugated metal sheets are a preferred option for both professionals and do-it-yourselfers.

It’s crucial to gather all required tools and materials before you start. Corrugated metal sheets, roofing screws, a screwdriver bit for your drill, a measuring tape, a chalk line, safety gloves, and safety glasses are all you’ll need. Make sure you have a sturdy ladder or scaffolding so you can get to the roof securely.

To start, measure the size of your roof to estimate the number of corrugated sheets you’ll need. Carefully consider the layout to reduce waste and guarantee appropriate drainage. To ensure that you adhere to any requirements regarding roof pitch and installation techniques, it is imperative that you review your local building codes and regulations.

Start the installation process at a corner of the roof, making sure the first sheet is slightly overhung for drainage and aligned with the edge. Install roofing screws in the valleys of the corrugated metal where they will be less noticeable and less likely to leak in order to fasten the sheet to the roof deck.

Lay the remaining sheets on top of each other, making sure they overlap to stop water seeping in. To ensure a polished appearance and maintain straight rows, use a chalk line. With tin snips or a metal cutting saw, trim sheets as necessary to fit around vents, chimneys, or other roof penetrations.

After all of the sheets are installed, check the roof for any gaps or loose screws. To stop rust and water intrusion, apply roofing sealant to any exposed screw heads. Lastly, tidy up any leftover debris from the installation process and properly dispose of it.

You can successfully install a corrugated metal roof that not only protects your home but also enhances its aesthetic appeal by carefully following these instructions and taking all necessary safety precautions. A corrugated metal roof can increase the overall value of your home and offer years of dependable service with regular maintenance.

Preparation of the material

You are able to order profiled sheets as soon as you have completed all of the precise roof calculations. If, after purchasing the sheets, you are unable to install them for any reason—for instance, rain—you will need to store the sheets in a closed space on a level surface, keeping the factory packaging on them. Furthermore, it is advised to place the bars 50 centimeters below the sheets.

This covering material needs to be moved and shifted very carefully. Be sure to hold it by the edges all the way along and to avoid bending or crease the sheets in particular. Since contemporary polymer coating is thought to be especially vulnerable to mechanical damage, the corrugated board needs to be handled carefully when being moved. Use abrasive cutting tools to cut the material; the areas where the cut is present will be significantly heated, and pieces of the circle may cause severe hand scratches. Should this still be required, repair paint needs to be applied right away to all of the damage.

Thankfully, corrugated board roofing technology currently permits all installation work to be completed during the warm season, which runs from April to October, saving you from having to store the material for an extended period of time.

Step-by-step installation workshops

Although this may come as a surprise to some, the information needs to be presented in various ways at first. Because each manufacturer provides unique styling recommendations, the situation here is entirely within the manufacturers; these recommendations are extremely significant. Even though these differences may not be significant, profile sheets from various firms are demanding regarding their terms. Because they want to do things their own way and because "they ate the dog on such roofs," fully hired workers should not be trusted. Instead, they should carefully read the instructions that are attached to the roofing material.

Thin metal profile

Should you choose a profile with a thickness of less than 0.7 mm for the roof installation, it is not recommended to style the roof directly along it as this could result in damage. As a result, you will need to lay down wooden science, which will require walking.

Detailed instructions:

1. Cut the required number of sheets.
2. Check the presence of all future elements for the roof.
3. Start styling from below, from the end of the roof. The first sheet should be mounted in the center of the deflection of the shelf and fixed with one screw.
4. The following sheets are placed overwhelmed, attached with screws.
5. The screws are screwed perpendicularly into the internal shelves of the profile, another arrangement of self -tapping screws can lead to deformation of sheets.
6. Several sheets already stacked in this way must be leveled with a special tracer lace.
7. The resulting part must be attached to the cladding.
8. If the length of the metal sheet corresponds to the size of the roof slope, then it must be attached to the skate in the center.

Roofing corrugated board

A wooden substrate is no longer suitable when working with such material.

Masterful installation of a metal profile roof:

1. The fastening of the corrugated board should begin with the layering from the lower corner of the first sheets. Align the sheets must be relative to the cornice. These sheets are connected with each other.
2. If the length of the slopes is longer than the sheets, then after laying the first row of the corral in parallel, the other sheets must be laid with transverse overlap.
3. Moreover, the more the slope of the slopes will be observed, the less should there be. The maximum overwhelming 20 cm is performed on roofs at about an angle up to 15 degrees. The width of the overlap will also depend on the height of the profiled sheet. If we are talking about a low profiled sheet, then there should be at least two waves.
4. The length of the length of metal sheets should be from 15 to 20 cm.
5. At the same time, screws are screwed with accurate calculation, since insufficient or excessive fastening of corrugations can lead to a decrease in the operational properties of the material.

Tightness is the primary marker of a well-installed roof. The purpose of the roofing material is to shield all internal structures from the elements and moisture. In the future, even a tiny gap could cause serious issues due to missing dampness and subdecks, which can lead to the growth of fungus and material damage.

Wind protection and waterproofing

At the moment, the market is able to provide a broad range of materials with varying species and characteristics.

The following steps are implied by waterproofing and wind protection:

1. Fix the selected waterproofing material on the rafters. For this action, you need to take the simplest construction stapler, but before direct laying it is worth checking whether you are going to lay a membrane or film that side. The panel should be glued together with a special ribbon.
2. Next, it is necessary to break through the racks of the rails, the thickness of which is at least 2 cm, and form a gap for ventilation necessary for ventilation for ventilation.
3. Roof material is further placed on the crate.

Installing waterproofing for corrugated board step-by-step:

1. Put the horizontally waterproofing film in the direction from the cornice strip to the ridge.
2. Leave 150 mm overwhelming with a sagging 20 mm film between the rafters.
3. When the film is laid, it must be tightly connected, glue, glue the joints carefully using adhesive tape.
4. Using a gap between the crate and the film, you can increase the overall ventilation efficiency. The width of this gap should be 5 cm.
5. So that the air passes freely through the roofing horse, it is necessary to leave a gap of 5 cm between the film and the roof skate.
6. Profile sheets are attached to the run using galvanized screws with a sealed puck. The lower part of the wave is attached, as well as all subsequent sheets that should cover the previous.

The procedure for laying sheets

The majority of roofers are installed in this manner: begin with the bottom row, place four sheets there initially, and fasten each sheet to a single self-tapping screw in the middle. Subsequently, 4.8 × 19 mm self-tapping screw sheets are connected; these should be installed in 50 cm increments. Subsequently, it is imperative to verify the alignment of the metal sheets along the roof overhang, and subsequently install the roofing material.

When installing a roof for the first time, profiled sheets need to be attached in the following order to prevent distortion:

1. The first sheet is installed on the crate, fastened with one screw at the skate itself.
2. The second profile fits in such a way that the lower edges of both sheets from below make up one perfect even line.
3. Next, it is necessary to fix it over the top of the wave under the first transverse fold.
4. To evaluate by eye, how correctly the profiled sheets are incorporated. If unevenly, then you need to raise one sheet from the other, slightly tilt it with the movement from the bottom up, and then shake the fold again behind the fold. Fix everything with self -tapping screws on top of the waves.
5. These actions must be done with 3-4 sheets, to align them carefully on the cornice, and then install the rest of the profiled sheets.

The corrugated board needs to be mounted at the base of the roof such that the edge is removed 4 cm from the cornice. This is necessary to ensure that the roof ventilation is not obstructed and that the skates have the ideal gap.

High -quality screws

Approximately six screws are used for every square meter when installing a corrugated board roof. The dimensions for this installation are 4.8 × 28–35 mm. These screws work with both metal and wood. Roofing material manufacturers also sell screws that come with a unique tool called a nozzle. The battery-operated electric drill is another option.

Specialized fasteners for roofing Professionals who do things themselves are essential because they can only offer the following services:

• High strength strength.
• Complete water resistance of the material.
• The minimum risk of mechanical trauma of the coating during fastening, which means that this will talk about the absence of corrosion in the future.

Accurate and superior self-tapping screws are available from the same suppliers that deal with corrugated board installation. Selecting zinc-coated carbon steel or stainless steel screws is advised. All sealing washers must still be thoroughly inspected before purchasing these components.

Correct mount

Recognize whether or not the screwdriver is positioned correctly by looking at a metal washer; there should be a rubber gasket there by roughly 1 mm.

When fastening screws into corrugated board, they must be inserted precisely perpendicular to the direction of the vertical wave deflection. While many builders disagree on this point, each approach has benefits of its own. For instance, the most dependable mount is produced by a self-tapping screw in the lower wave, and in the upper wave, there is less possibility of rainwater seeping under the roofing space.

However, corrugated board manufacturers advise accurately adjusting it in the deflection. The screws must be inserted into the deflection through the wave on the crest and cornice, and into each board of the crate in the center of the sheet. Each square meter has between five and eight screws total.

Our installation guide for corrugated metal roofing takes you step-by-step through the process of replacing your roof with profiled sheets. We offer helpful advice and unambiguous instructions for handling this project with confidence, covering everything from setup and required materials to intricate installation methods. This article gives you the skills necessary to install corrugated metal roofing on your own, whether your goal is to improve the longevity of your home or update its visual appeal.

Necessary tools

It is important to note that even someone with no prior construction experience can easily install corrugated board on a roof. Of course, there are roofing materials that require skilled professionals to install correctly. However, when it comes to contemporary corrugated board, anyone can handle installation on their own.

The roof slopes overlap without the need for additional transverse joints because of the cornfield’s great length, and this material is simple to cut and adjust. The following installation tools are necessary:

• Electric sedimentary scissors.
• Shurovyrt.
• Drill for cutting metal.
• Ticks "Hofra".
• Metal hand scissors.
• Hand -on charging scissors for metal.
• Rag.
• Nozzle on a screwdriver 8 × 45.

The profile can be laid on slopes with practically any inclination; all that is required is accurate transverse overlap calculation:

• 100-150 – mm at large corners.
• 200 mm – for a slope of 14 degrees.
• 150-200 – mm for roofs with 15-30 degrees.

You will need self-tapping screws with specific ME pucks in order to attach corrugated board.

Installing corrugated metal roofing sheets can improve your home’s durability and aesthetic appeal, making it a rewarding do-it-yourself project. Many homeowners choose corrugated metal roofs because of their reputation for strength and resilience to the elements.

Getting all the tools and supplies needed is crucial before beginning the installation process. Corrugated metal sheets, fasteners, a drill bit for a screwdriver, a tape measure, a chalk line, and safety equipment like goggles and gloves are usually included in this. An easier installation procedure is guaranteed when everything is ready in advance.

Make sure the roof surface is clean, dry, and clear of any debris before starting. To add more protection and insulation, install the roofing underlayment or insulation layer after that. By taking this step, condensation inside the roof structure is prevented and energy efficiency is improved.

To create a tight seal against wind and rain, begin at one corner of the roof and work your way across while installing the corrugated sheets, overlapping each one as you go. To firmly secure the sheets to the roof structure, use the appropriate fasteners, usually screws made for corrugated metal, and place them strategically along the overlapping edges.

In order to stop water from seeping in, trim any extra material and make sure all edges are properly sealed. Frequent upkeep, like checking for broken sheets or loose screws, will help your corrugated metal roof last longer. A corrugated metal roof can increase the overall appeal of your house and offer decades of dependable service with proper installation and upkeep.

Video on the topic

Construction affairs. How to correctly lay a profiledist on the roof of the house!

Installation of corrugated board on the roof. Complex eight -sloping roof from a profiled sheet and its limited installation.

Roofing from corrugated roofs with your own hands

Roof installation alone. How to raise corrugated board to the roof one. Installation of a metal roof

Where to twist screws? Up or down the waves

Installation of corrugated board on the roof. Roof installation

Installation of corrugated board (metal profile) with your own hands. My first experience and errors during installation!.

Installation of roofs from corrugated board