Foam facade plaster

Foam facade plaster is a game-changer when it comes to improving the outside of your house. This cutting-edge material is a favorite among architects and homeowners alike because it has both functional advantages and visual appeal.

Foam facade plaster, commonly referred to as exterior insulation and finish system (EIFS), is composed of a weather-resistant, long-lasting finish applied to a lightweight foam board. This combination not only increases your home’s insulation but also offers a flexible space for imaginative design ideas.

The energy efficiency of foam facade plaster is one of its main benefits. It helps control indoor temperatures by adding an additional layer of insulation to the outer walls, which lowers the need for heating and cooling. This promotes environmental sustainability in addition to lowering energy costs.

In addition to its practical advantages, foam facade plaster provides an extensive array of design options. It can simulate a variety of textures, including brick, stone, and stucco, to give your house a unique appearance without the cost or weight of conventional materials. Because of this flexibility, homeowners can maintain practicality while achieving their desired aesthetic.

The plane of the foam should be prepared

We examine the plates to see if there are any gaps. Very few people are able to install the insulation precisely the first time. If this step was overlooked during installation, we seal the joints. Since the adhesive solution is subsequently applied in thin layers, pay close attention to the curvature of the entire plane. The peculiarities of the composition will prevent irregularities from aligning. You can fill in the spaces between the foam stoves by using foam for insulation systems, such as Ceresit CT-84, which is typically mounted. One spray can (850 ml) will require approximately 600 r.

The use of foam insulation for the facade

Prices for foam

Foam

We make a plaster solution

Use of a typical sand-based solution with sand is not advised. He won’t give the plaster’s composition good quality. There are a ton of combinations in the store that are appropriate for styling foam, based on composition.

Skilled finishers recommend using:

• "Stolit",
• "Ceresit",
• "Ecomix".

Pay close attention to the kneading instructions provided by the manufacturer on the packaging. Skilled artisans create a mixture that has a strong sour cream-like flavor. The mixture consistency should be slightly slurry than what the manufacturer specifies in order to glue the fiberglass grid. When it comes to the leveling layer, the mixture ought to be so fluid that it pours easily off the spatula. This explains the disparity in composition consumption: 4 kg of the mixture are needed for each square meter when adhering the grid, whereas 6 kg are needed for the leveling layer.

Making plaster solution

Despite their greater similarity, compounds made by different manufacturers have different components. To avoid needless issues, it is therefore preferable to use products from the same manufacturer on the same object.

Employ universal compounds so you won’t have to worry about extra subtleties related to scope limitations.

Prices for popular types of plaster

Plaster

Primary layer sampling

Installing the first layer of foam will prepare it for plastering. A PVC grid stable was placed in front of the alkaline for this reason. You can protect yourself from the damaging effects of cement on the displayed grid by using PVC. As you are aware, cement reacts with a variety of substances.

Make cuts in stripes that are just a little bit longer than the wall’s height. Remember that styling is done from head to toe. Using one hand, secure the strip to the fiberglass, and then use the other to apply the solution only to the upper edge of the mesh. The grid and foam are thus "welded" together. Consequently, the thickness of the primary layer should be as high as 5 mm.

Insulation scheme using foamyx: Foam troops (1), glue (2), dowel (3), and reinforcing mesh (4) Five is primer; six is plastering coating.

When the pump is obstructed by a wall, you should apply a suction cup to the surface so that the pump is evenly distributed throughout the entire field. Every motion is made from top to bottom. Because each new strip will disappear to the edge of the preceding one by nearly 1 centimeter, make sure to leave a vertical "tape" free of plaster mix.

Consequently, the wall appears to be a strip behind a strip that has a net covering the entire surface. Examine every area of the wall where the plane’s geometry varies, such as door openings, slopes, and window openings. To begin with, you must begin laying the grid.

Foam

Prices for reinforcing nets for foam

Foam

A flexible way to improve the external appearance and usability of your home is with foam facade plaster. It is perfect for a variety of weather situations because it combines lightweight materials with durable qualities. This kind of plaster gives your facade a sleek, contemporary appearance in addition to improving insulation. Foam facade plaster offers a cost-effective approach to attain energy efficiency and fashionable curb appeal, whether you’re building from scratch or remodeling, making sure your house stands out while remaining well-protected from the weather.

Smoothing the first layer

The goal of this process is to create a flat, monolithic base beneath the second layer. Align the whole aircraft while lightly pressing down on the foam after wetting the lower half with water. It is typical for us to ignore the portions of the grid that are displayed as we work through the solution. It occurs that skilled professionals prime the first layer once more after waiting for a solution to dry.

The final finish by the mixture

The second layer is required to finish the wall’s alignment and conceal any auxiliary components, like reinforcement. If for some reason the master is not liked by the quality of the second layer, then the third layer can be possible. However, this is merely a "black" ornamentation until the last phase, which is the surface’s final design. Decorative plaster is typically used for the final stage. It is not appropriate to discuss the standard installation of "decoration" if the surface was unevenly prepared.

Plaster of foam for facades

Table: Materials and tools required.

What needs to be provided

Determine the total amount to be purchased before making any plaster material purchases. When laying the first layer, the mixture consumption will be less than 4 kg/m2 if the installed technology is used. Between 5.5 and 6.5 kg/m2 will be needed for the second layer.

One piece of advice is to have extra mixture on hand in case you need to quickly create a third corrective layer.

A flexible way to improve the external appearance and usability of your home is with foam facade plaster. This lightweight material is a popular choice for both builders and homeowners because it combines the advantages of insulation with a smooth, attractive finish.

Foam facade plaster’s superior thermal insulation qualities are one of its main benefits. You can greatly increase your home’s energy efficiency by minimizing heat gain in warmer months and reducing heat loss in the winter by adding a layer of foam plaster to the exterior of your building.

The resilience to weathering and longevity of foam facade plaster are additional attractive qualities. Unlike conventional materials, foam plaster won’t break easily and can endure inclement weather, wind, rain, and UV rays, giving your house long-lasting protection.

Foam facade plaster has aesthetic benefits in addition to its practical ones. It is simple to modify to create a variety of textures and colors, giving homeowners the ability to design a unique aesthetic that accentuates curb appeal and blends in with their architectural style.

All things considered, foam facade plaster is the best option available to homeowners looking for an affordable, environmentally friendly, and aesthetically pleasing way to improve the outside of their houses. When building a new home or remodeling an old one, think about the advantages that foam facade plaster can provide for both protecting and changing your house.

Video on the topic

Plaster at home. Plaster at home by foam.

Installation of insulation for simulating stone from A to Z.

See what happened to the plaster on the foam

How to plaster a foam