DIY wild stone is easy and in detail

Plotnyak, or wild natural stone, is a magnificent building material in every way.

It can be used to finish the facade of a private home or to make ornamental garden paths. The question of how to lay wild stone becomes particularly important when designing a landscape that will blend in with nature as much as possible and contain intricate technical features in the park or yard area.

Wild stone garden paths require very little upkeep and can last for many decades.

The following are wild stone’s primary benefits:

1. Inexpensive natural fossil, which is resistant to chemical and mechanical influences.
2. Easy to process the cutting tool.
3. Environmentally friendly.

Furthermore, the durability of the stone can guarantee that a coating applied to pathways, walls, and floors will satisfy the owner for a considerable amount of time without the need for ongoing maintenance or surface restoration.

The following materials are required to create a wild stone styling with your hands:

Using a construction mixer to mix the cement-sand mixture is the most practical method.

• brush;
• solvent;
• waterproofing material (in the case of a wooden surface);
• metal mesh (if installation is carried out on a wooden or metal surface);
• soil (for metal surfaces);
• cement-sand mixture (in the case of a metal surface);
• wild stone;
• cement;
• plasticizers;
• sand;
• special mounting corners;
• bitumen mastic;
• grinding machines or stones with a diamond disk;
• special tool for extending;
• special moisture -resistant solution;
• Metal trowel or spatula.

Preparing the surface before laying wild stone with your own hands

It is crucial to keep in mind that placing stone cannot be done without first determining its strength. This is because different plate varieties can have varying percentages of interspersed extraneous materials, sand, and lime solutions. Practically anyone with even a passing knowledge of the initial wall preparation techniques can lay wild stone. The salient features of this kind of work will be further examined.

1. If there is a concrete surface, it is worth knowing that special preparation of such walls is not required. The only thing to do is to remove all fat spots and other dirt, if any. Failed paint can be removed using a brush, and oil spots can be cleaned with a solvent.

It is essential to treat wooden or metal surfaces with waterproofing and materials to increase the adhesiveness before laying wild stone on them.

Do -it -yourself wild stone installation

A natural stone is placed on a cushion of gravel and sand to create a garden path. This allows drainage water to pass freely beneath the stone.

Initially, if the tile does not have the only template size, you need to lay out the stone on the surface so that the pattern is formed and it became clear where and which wild stone would need to be attached. In order to unique the drawing, it is recommended to alternate stones of various shapes and shades. Thus it will be possible to create a really natural pattern. It will be necessary to plan it before laying. In this case, it will be necessary to rearrange each tile according to the impromptu pattern. The finished pattern will look especially impressive if you use the alternation of large and small plates of such a stone. It is not recommended to lay stone in frost. This is due to the fact that the glue on which the material will need to be mounted will not be able to freeze, but simply freeze. This is fraught with the consequences in the thaw, it will be possible to see how some tiles (or even completely all) will simply disappear.

Decorating the spaces between tiny gravel stones is very popular.

Laying wild stone is very similar to the installation work of decorative ceramic tiles. First of all, it is necessary to knead the adhesive mixture based on cement, plasticizers and sand. In this case, the option of using bitumen mastics is possible, which can improve the quality of gluing such stones to almost any surfaces. To stick a similar stone, you will need to use any glue for tiles or cement mortar. However, it will be best to purchase special mastic of terrapast from the manufacturer Terraco. Such mastic is immediately ready for use, will have a very pleasant consistency, quite viscous so that it does not flow and does not spray and at the same time comfortably fit. Tiles on such mastic can stick to the wall in a matter of seconds. Within the first 10-15 minutes, it can be torn without any special effort. In an hour, it will be a finished coating that is not subject to adjustment.

A metal mesh is also laid in addition to the wild stone to improve the solution’s adhesion to the wall.

The cost of such a mastic is greater, however, the consumption is less than the one that could have a solution or cement glue, because a sufficient thickness of the mastic can be only 2-3 mm. Mastic can be applied both directly to the tile of the stone, and on the base. The main thing here is to foresee that the adhesive surface does not fall on the surface of the sandstone, since it is then quite difficult to wash and clean it. In some cases, to lay wild stone on the walls, it may be necessary to use corner elements that can smooth out, brighten up and decorate the uneven angle. For this, special mounting corners are produced and sold, which subsequently can be inserted into a layer of glue mixture before laying the stone. After that, the tile itself lies on top.

The construction level determines how smoothly natural stone is laid.

Therefore, the corner will be able to easily fit the stone and will be reliably attached, hardening along with the solution. After a layer of mastic is applied, the tile of the stone is applied to the surface and slightly crushed. Work should start only from the lower, horizontal series. Further, laying is gradually performed over the entire surface of the base or wall. In the process of laying wild stone with your own hands on a horizontal surface, for example, as a garden path, you will need to lay the tile starting from the farthest edge of the path. After that, you need to gradually approach the beginning of the territory of the house or the entrance to the courtyard itself.

Laying complex figures made of wild stone with your own hands

Because natural stone is so simple to work with, you can create stunning, seamless styling.

As mentioned earlier, wild stone is able to easily succumb to machining with an electric tool. This can be, for example, a grinding machine or a stone -register with a diamond disk that can cut wild stone in all possible directions. Stone tile is possible to make almost any size and forms. It may also be needed if the project was conceived that all the seams of the tiles will be the same in size and thickness. Therefore, without cutting tools, it will not work to do here. Chips and places of cutting stones must be immediately treated with mastic, which will protect them from destruction from time to time and if moisture falls inside.

Usually, wild stone is offered for sale in square meters or in boxes. There could be two or three slabs in the box. Generally speaking, tiles only vary in size. This will arrange different drawing ranks and prevent joints from occurring one above the other. It is advised to check that each time that the tile joints are in new locations. This is required to prevent patterns from being seen by the eye. Achieving the most natural wild surface can be facilitated by combining while considering this rule.

DIY seam decoration process

It’s crucial to keep an eye out to make sure the decorating solution doesn’t spill onto the slabs when decorating the spaces between the stones.

In the process of laying wild stone, you must try to make the seams as smooth as possible (it means the distance between each pebble). For this, a special retreating tool was created, which is able to help make seams the same as the same. This can also be done if the stone tiles were made of various shapes. In the process of sealing the seams, it is necessary to ensure that the mastic does not fall directly onto the tile, it should only remain in the seams. It is not recommended to use iron brushes at all, because they can break the structure and color of the stones. The seam itself will need to be filled with a special moisture -resistant solution. It should be applied with a wooden stick, while pressing into the seam. After he begins to harden, it is necessary to remove surpluses with a narrow metal trowel or a spatula.

It is important to note that perfectly straight and maximum even seams can give the entire wild stone pattern a polished, well-balanced appearance. If it was supplied for laying a fully flat tile VSK, DIY sutures might not be necessary and can be completed with your hands. The stones remain unprocessed because they are securely attached to one another on all sides during the seamless laying process.

With the appropriate method, you can create a detailed and attainable DIY wild stone facade for your home. This article walks you through the simple steps and necessary information needed to update the exterior of your home. You’ll learn how to create a facade that looks professional without having to pay a fortune for expert assistance, from choosing materials that mimic natural stone to the detailed installation procedure. This guide makes sure that every detail, from planning to finishing touches, is covered in a way that makes the process simple and pleasurable, even for beginners, whether you’re improving curb appeal or adding a rustic charm.

The question "wild stone: with your own hands" piques people’s curiosity. The fact that this material is environmentally friendly has made it very popular.

Video on the topic

Art concrete. Decorative rock. From A to Z.

DIY decorative stone – very cheap and easy

Cement stone. It"s not at all difficult.

DIY decorative stone. Stucked stone. Gas block plaster. The decor of the facade

DIY decorative plaster painting. Master Class.

5 methods of applying decor under stone! Imitation of stone. Useful tips.

DIY artificial stone The whole manufacturing process + correct gypsum proportions. 4K

DIY artificial stone with a rock part 1 shape for stone.